Bobcat T40140 / T40180 Telescopic Handler Fault Codes

The following error messages may be displayed:

[NONE] - no service codes.

[REPLY] - The dashboard is not communicating with the controller.

[SHTDN] (Off) - Disabled state.

Press and hold the info button (item 1) for three seconds to return to the engine hours menu.

Service Code List - Engine Controller

CODE DESCRIPTION RESULTS

E000100-03 Oil pressure sensor error; signal above control range

E000100-04 Oil pressure sensor error; signal below control range

E000102-02 The charge air pressure is above the threshold level for warning

E000102-02 The charge air pressure is above the threshold level for shutdown

E000102-03 Charge air pressure sensor error; signal above control range

E000102-04 Charge air pressure sensor error; signal below control range

E000105-00 High charge air cooler temperature; value above the warning threshold

E000105-00 High charge air cooler temperature; value above the threshold for shutdown

E000105-03 Discharge air temperature sensor error; signal above control range

E000105-04 Discharge air temperature sensor error; signal below control range

E000110-00 Coolant temperature too high; value above the warning threshold (111 ° C)

E000110-00 Coolant temperature too high; value above the switch-off threshold (119 ° C)

E000110-03 Coolant temperature sensor error; signal above control range

E000110-04 Coolant temperature sensor error; signal below control range

E000157-03 Line pressure sensor error; signal above control range

E000157-04 Line pressure sensor error; signal below control range

E000164-02 Line pressure protection function is not performed properly

E000168-00 Physical test detected too high battery voltage

E000168-01 Physical test detected too low battery voltage

E000168-02 High battery voltage; value above the warning threshold

E000168-02 Low battery voltage; value above the warning threshold

E000168-03 Battery voltage sensor error; signal above control range

E000168-04 Battery voltage sensor error; signal below control range

E000190-00 Engine speed above threshold level for warning (FOC level 1)

E000190-02 Too large angle between the crankshaft and camshaft sensors

E000190-08 Camshaft speed sensor; unstable signal

E000190-08 Crankshaft speed sensor; unstable signal

E000190-011 Motor speed above threshold level for warning (FOC level 2)

E000190-012 Camshaft speed sensor; no signal

E000190-012 Crankshaft speed sensor; no signal

E000190-014 Engine speed above warning threshold (overspeed mode)

E000190-014 The signal from the crankshaft and camshaft speed sensor is not available on the CAN bus

E000520-09 Timeout error for receiving frame on the CAN bus TSC1TR; set value

E000630-012 EEPROM memory access error (delete)

E000630-012 EEPROM memory access error (read)

E000630-012 EEPROM memory access error (write)

E000639-014 CAN bus 0 (state - bus off)

E000651-03 Injector 1 (in ignition order); short circuit

E000651-04 Short circuit from high voltage side to low voltage side in injector 1 (in ignition order)

E000651-05 Injector 1 (in ignition order); broken electrical connection

E000652-03 Injector 2 (in ignition order); short circuit

E000652-04 Short circuit from high voltage side to low voltage side in injector 2 (in ignition order)

E000652-05 Injector 2 (in ignition order); broken electrical connection

E000653-03 Injector 3 (in ignition order); short circuit

E000653-04 Short circuit from the high voltage side to the low voltage side in injector 3 (in the order of ignition)

E000653-05 Injector 3 (in ignition order); broken electrical connection

E000654-03 Injector 4 (in ignition order); short circuit

E000654-04 Short circuit from high voltage side to low voltage side in injector 4 (in ignition order)

E000654-05 Injector 4 (in ignition order); broken electrical connection

E000676-011 Cold start auxiliary relay error.

E000676-011 Load of opening auxiliary cold start relay

E000677-03 High voltage side of starter relay; short circuit to battery

E000677-03 Low voltage side of starter relay; short circuit to battery

E000677-04 High voltage side of starter relay; short circuit to ground

E000677-04 Low voltage side of starter relay; short circuit to ground

E000677-05 Starter relay; error - no load

E000677-012 Starter relay; high temperature in the feeding phase

E000729-05 Opening load of auxiliary cold start relay

E000729-012 Auxiliary cold start relay; error - excessive temperature

E000898-09 TSC1TE CAN bus frame receive timeout error; set value

E001079-013 Sensor 1 supply voltage monitor error (ECU)

E001080-013 Sensor 2 supply voltage monitor error (ECU)

E001109-02 Request to turn off the engine is ignored

E001136-00 Physical test detected too high ECU temperature

E001136-01 Physical test detected too low ECU temperature

E001136-03 ECU temperature sensor error; signal above control range

E001136-04 ECU temperature sensor error; signal below control range

E001231-014 CAN bus 1 (state - bus off)

E001235-014 CAN bus 2 (state - bus off)

E001322-012 Too many misfire detected in multiple cylinders

E001323-012 Too many cylinder 1 misfire detected (in ignition order)

E001324-012 Too many misfire detected in cylinder 2 (in ignition order)

E001325-012 Too many cylinder 3 misfire detected (in ignition order)

E001326-012 Too many cylinder 4 misfire detected (in ignition order)

E002797-04 Diagnosis of the injector; earth fault measurement timeout error - cylinder group 0

E002798-04 Injector diagnostics; earth fault measurement timeout error - cylinder group 1

E002798-04 Injector diagnostics; earth fault monitoring - check cylinder bank 0

E002798-04 Injector diagnostics; earth fault monitoring - check cylinder bank 1

E523008-01 Manipulation control was initiated

E523008-02 Keying control timeout error

E523009-09 The maximum permissible number of openings of the pressure relief valve has been reached

E523009-010 The maximum permissible opening time of the pressure relief valve has been reached.

E523212-09 CAN frame receive timeout error ComEngPrt; motor protection

E523216-09 CAN bus frame receive timeout error PrHtEnCmd; preheat command, motor command

E523240-09 CAN bus timeout message FunModCtl; operating mode control

E523330-014 Immobilizer status; fuel filter clogged

E523350-04 Injector, cylinder group 1; short circuit

E523352-04 Injector, cylinder group 2; short circuit

E523354-012 Injector output defect on the supply phase

E523470-02 Pressure relief valve forced opening (PRV); performed under pressure conditions

E523470-02 Pressure relief valve forced opening (PRV); performed under shockwave conditions

E523470-07 Maximum line pressure exceeded in emergency mode (PRV)

E523470-011 PRV cannot be opened at this stage of the operating procedure under shockwave conditions

E523470-011 Line pressure out of range

E523470-012 Opening of the pressure relief valve (PRV); shutdown state

E523470-012 Pressure relief valve (PRV) opening; warning state

E523470-014 Pressure relief valve (PRV) open

E523550-012 Start switch T50 active for too long

E523601-013 Sensor 3 supply voltage monitor error (ECU)

E523605-09 TSC1AE CAN bus frame receive timeout error; traction control

E523606-09 CAN frame receive timeout error TSC1AR; deceleration mechanism

E523612-012 Firmware error (ECU); injection closure

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Detection error during internal monitoring of the ECU

E523612-012 Firmware error (ECU)

E523612-014 CPU software reset (CPU SWReset_0)

E523612-014 CPU software reset (CPU SWReset_1)

E523612-014 CPU software reset (CPU SWReset_2)

E523613-00 Maximum positive deviation of pressure in the line exceeded (RailMeUn0)

E523613-00 Maximum positive pressure deviation in the metering device line (RailMeUn1) exceeded

E523613-00 Line system leak detected (RailMeUn10)

E523613-00 Maximum negative pressure deviation in the metering device line (RailMeUn2) exceeded

E523613-00 Negative deviation of line pressure in the second phase (RailMeUn22)

E523613-00 Maximum rail pressure exceeded (RailMeUn4)

E523613-01 Minimum rail pressure exceeded (RailMeUn3)

E523613-02 Dosing device setpoint in overspeed mode is invalid

E523615-03 Metering device (fuel system); short circuit on the high voltage side of the battery

E523615-03 Metering device (fuel system); short circuit on the low voltage side of the battery

E523615-04 Metering device (fuel system); short to ground (high voltage side)

E523615-04 Metering device (fuel system); short to ground (low voltage side)

E523615-05 Metering device (fuel system); opening load

E523615-012 Metering device (fuel system); high temperature in the feeding phase

E523698-011 Switch-off request from the control monitoring function

E523717-012 AmbCon CAN frame transmission timeout error; weather

E523766-09 TSC1AE bus frame receive timeout error; actively

E523767-09 CAN frame receive timeout error TSC1AE; passively

E523768-09 CAN frame receive timeout error TSC1AR; actively

E523769-09 CAN frame receive timeout error TSC1AR; passively

E523770-09 TSC1DE CAN bus frame receive timeout error; passively

E523776-09 TSC1TE CAN bus frame receive timeout error; actively

E523777-09 CAN frame receive timeout error TSC1TE - passive; set value

E523778-09 CAN frame receive timeout error TSC1TR - active

E523779-09 TSC1TR bus frame receive timeout error - passive

E523895-013 Checking the absence of a programmable setting value for injector 1 (in the order of ignition)

E523896-013 Checking the absence of a programmable setting value for the injector 2 (in the order of ignition)

E523897-013 Checking the absence of a programmable setting value for injector 3 (in the order of ignition)

E523898-013 Checking the absence of a programmable setting value for injector 4 (in the order of ignition)

E523913-03 Sensor error - voltage in the glow plug diagnostic line; signal above control range

E523913-04 Sensor error - voltage in the glow plug diagnostic line; signal below control range

E523914-03 Glow plug control; short circuit to battery

E523914-04 Glow plug control; short circuit to ground

E523914-05 Glow plug control; opening load

E523914-05 Glow plug control reset line; error - short circuit

E523914-011 Glow plug control; Internal error

E523914-012 Glow plug control; high temperature in the feeding phase

E523929-00 Fuel balance control integrator injector 1 (in ignition order); maximum value exceeded

E523929-01 Fuel balance control integrator injector 1 (in ignition order); minimum value exceeded

E523930-00 Fuel balance control integrator injector 2 (in ignition order); maximum value exceeded

E523930-01 Fuel balance control integrator injector 2 (in ignition order); minimum value exceeded

E523931-00 Fuel balance control integrator injector 3 (in ignition order); maximum value exceeded

E523931-01 Fuel balance control integrator injector 3 (in ignition order); minimum value exceeded

E523932-00 Fuel balance control integrator nozzle 4 (in ignition order); maximum value exceeded

E523932-01 Fuel balance control integrator injector 4 (in ignition order); minimum value exceeded

E523935-012 CAN frame transmission timeout error EEC3VOL1; sent engine messages

E523936-012 CAN frame transmission timeout error EEC3VOL2; sent engine messages

E523946-00 Zero calibration fuel injector 1 (in ignition order); maximum value exceeded

E523946-01 Zero calibration fuel injector 1 (in ignition order); minimum value exceeded

E523947-00 Zero calibration fuel injector 2 (in ignition order); maximum value exceeded

E523947-01 Zero calibration fuel injector 2 (in ignition order); minimum value exceeded

E523948-00 Zero calibration fuel injector 3 (in ignition order); maximum value exceeded

E523948-01 Zero calibration fuel injector 3 (in ignition order); minimum value exceeded

E523949-00 Zero calibration fuel injector 4 (in ignition order); maximum value exceeded

E523949-01 Zero calibration fuel injector 4 (in ignition order); minimum value exceeded

E523982-00 Power phase diagnostics disabled; high battery voltage

E523982-01 Power phase diagnostics disabled; low battery voltage

E524035-012 Injector diagnostics; SPI communication timeout error

E524036-012 Diagnostics of the auxiliary injector; SPI communication timeout error

E524057-02 Electric fuel pump; fuel pressure build-up error

E524118-09 ComRxCM1 CAN frame receive timeout error

Service Code List - Gateway Controller

The gateway controller is located in the cockpit behind the right instrument panel and display panel.

M0309 Low battery voltage All functions enabled

M0310 Battery voltage high All functions enabled

M0311 Battery voltage extremely high All functions enabled

M0314 Battery voltage extremely low All functions enabled

M0322 Battery voltage below maximum permissible All functions are enabled

M0414 Engine oil pressure extremely low All functions enabled

M0415 Engine oil pressure at emergency shutdown level Engine shutdown

M0610 High engine speed All functions enabled

M0611 Extremely high engine speed All functions enabled

M0613 No engine speed signal Movement disabled

M0615 Engine speed at emergency shutdown level Engine shutdown

M0618 Engine speed out of range All functions enabled

M0710 High hydraulic oil temperature All functions enabled

M0711 Extremely high oil temperature in the hydraulic system.

M0715 Oil temperature in the hydraulic system at the emergency engine shutdown level.

M0810 Engine coolant temperature high All functions enabled

M0811 Engine Coolant Temperature Extremely High All functions enabled

M0815 Engine coolant temperature at emergency shutdown level Engine shutdown

M0821 Engine coolant temperature above maximum limit All functions enabled

M0822 Engine coolant temperature below minimum limit All functions enabled

M0909 Low fuel level All functions enabled

M0921 Fuel level above maximum limit All functions enabled

M0922 Fuel level below minimum limit All functions enabled

M1602 Front alignment indicator output, faulty activation All functions are enabled

M1603 Front alignment indicator output, erroneous shutdown All functions enabled

M1702 Rear alignment indicator output, faulty activation All functions enabled

M1703 Rear alignment indicator output, erroneous shutdown All functions enabled

M1821 Frame alignment potentiometer signal above limit frame alignment locked

M1822 Frame alignment potentiometer signal below limit frame alignment locked

M2405 Side control valve output, short to battery Movement reduced

M2406 Side control valve output, earth fault All functions enabled except side control

M2407 Side control valve output, open circuit All functions enabled except side control

M2505 Valve 4 wheels, short circuit to battery Movement reduced

M2506 4 wheel valve, ground fault 4 wheel steering not available

M2507 Valve 4 wheels, open circuit 4-wheel steering mode not available

M2648 Steering mode switch, multiple active inputs All functions enabled

M2702 Fan inverter output, erroneous power-up Fan inverter enabled

M2703 Fan inverter output, erroneous shutdown Fan inverter not available

M2707 Fan inverter output open circuit Fan inverter not available

M2805 Fan PWM output, short to battery Fan inverter not available

M2806 Fan PWM output, ground fault Fan inverter not available

M2807 Fan PWM output open circuit Fan inverter not available

M2832 Fan PWM output, overcurrent Fan inverter not available

M3128 Fault recovery mode Engine shutdown

M3204 No communication with workgroup controller Workgroup functions are disabled

M3404 No communication with display controller Information not displayed

M3604 No communication with engine controller Error - engine speed Movement disabled

Engine shutdown in case of Engine Controller failure

M3704 No signal from drive controller Travel and auxiliary hydraulic functions are disabled

M4109 Generator voltage low All functions enabled

M4110 Generator voltage high All functions enabled

M4304 No communication with the KSS keypad Manual cranking of the engine is prohibited (if previously blocked)

M4621 Encoder power supply outside upper range limit Influence on creep function

M4622 Encoder power supply below range limit Influence on creep function

M4805 Working light output, erroneous switching on Working light permanently on

M4806 Work light output, erroneous switch-off Work light not available

M5205 Electronic battery disconnect output, open circuit or short to battery

Open circuit: no power supplied If there is a short to battery (BSC): the electronic battery disconnect is always closed. All functions are enabled, but can remain closed when the key is in the OFF position.

M5206 Electronic battery cut-off output, ground fault No power supplied to machine

M5207 Electronic battery cut-off output, open circuit Power is not supplied to machine

M5302 Electronic battery cut-off, sticking Machine always receives power even though the key is in the OFF position.

M5303 Electronic battery cut-off, opening error (sticking) Power is not supplied to machine

M6105 Safety valve, short to battery Run group functions disabled

M6106 Safety valve, earth fault Run group functions disabled

M6107 Safety valve, open circuit Working group functions disabled

M6131 Safety valve, overcurrent Run group functions disabled

M7748 Multiple keys active (service tool and key) Do not turn engine over

M9999 Incorrect table with permanent data Gateway functions disabled Unable to crank the engine

Service Code List - Drive Controller

The drive controller is located between the boom and cab, next to the front frame fuse box.

CODE DESCRIPTION RESULTS

D0217 Clogged hydraulic filter All functions enabled

D0321 Battery voltage above maximum limit All functions are disabled

D0322 Low battery voltage below the minimum limit All functions are disabled

D0421 Slow pedal signal above the maximum limit Movement is reduced to 20%

D0422 Slow pedal signal below the minimum limit Movement is reduced to 20%

D0428 Slow pedal input error Movement is reduced to 30%

D1402 Brake light output, erroneous activation All functions are enabled

D1403 Brake light output, erroneous shutdown All functions are enabled

D1407 Brake light output, open circuit All functions enabled

D1433 Brake light output, internal fault All functions enabled

D1502 Brake light relay, erroneous activation All functions are enabled

D1503 Brake light relay, erroneous shutdown All functions are enabled

D1605 Forward drive pump coil, short to battery Movement disabled

D1606 Forward drive pump coil, short to ground Forward travel disabled

D1607 Forward drive pump coil, open circuit Forward travel disabled

D1632 Forward drive pump coil, overcurrent Movement disabled

D1705 Reverse drive pump coil, short to battery Movement disabled

D1706 Reverse drive pump coil, short to ground Reverse disabled

D1707 Reverse drive pump coil, open circuit Reverse disabled

D1732 Reverse drive pump coil, overcurrent Movement disabled

D2002 Low speed output (hydraulic motor), erroneous inclusion Movement is reduced to 30%

D2003 Low speed output (hydraulic motor) erroneous shutdown Movement is reduced to 30%

D2007 Low speed output (hydraulic motor) open circuit Movement is reduced to 30%

D2033 Low speed output (hydraulic motor), internal controller failure Movement is reduced to 30%

D2102 Slow speed relay, erroneous activation Movement is reduced to 30%

D2103 Slow speed relay, erroneous shutdown Movement is reduced to 30%

D2202 Cancel valve output (hydraulic motor), erroneous activation All functions are enabled

D2203 Cancel valve output (hydraulic motor), erroneous shutdown All functions enabled

D2207 Cancel valve output (hydraulic motor) open circuit All functions enabled

D2233 Override valve output controller, internal fault All functions enabled

D2302 Cancellation valve relay, erroneous activation All functions are enabled

D2303 Cancellation valve relay, erroneous shutdown All functions are enabled

D2502 Left stabilizer on the floor, erroneous activation All functions are enabled

D2503 Left stabilizer on the floor, erroneous shutdown All functions are enabled

D2609 Low pressure in the hydraulic steering wheel All functions are enabled

D2621 The pressure in the hydraulic steering wheel is below the maximum permissible All functions are enabled

D2702 Right stabilizer on the floor, erroneous inclusion All functions are enabled

D2703 Right stabilizer on the floor, erroneous shutdown All functions are enabled

D2821 Left stabilizer pressure sensor signal out of range All functions enabled

D2822 Left stabilizer pressure sensor signal out of range All functions enabled

D2921 Right stabilizer pressure sensor signal out of range All functions enabled

D2922 Right stabilizer pressure sensor signal out of range All functions enabled

D3204 No communication with the workgroup controller Auxiliary hydraulics disabled

D3304 No communication with the gateway controller All functions are disabled

D3404 No communication with the display controller All functions are disabled

D3604 No communication with the engine controller Movement disabled

D3723 Incorrect program or permanent data Movement disabled

D3728 Controller failure Movement disabled

D3796 Power off All functions enabled

D3797 Programmed by the controller All functions are enabled

D4004 No communication with joystick Movement prohibited / boom movement prohibited

D4011 Right joystick roller is not in neutral (auxiliary hydraulics) Auxiliary hydraulics disabled

D4028 Joystick handle failure Movement prohibited / boom movement prohibited

D4113 Lever FNR, no signal Movement disabled

D4128 FNR, multiple active inputs Movement disabled

D4621 5V voltage sensor output above maximum limit All functions are disabled, engine shutdown

D4622 5V voltage sensor output below minimum limit All functions are disabled, engine shutdown

D5521 Tilt plate sensor 1 signal above maximum limit Movement reduced

D5522 Tilt plate sensor 1 signal below minimum limit Movement reduced

D5621 Tilt plate sensor 2 signal above maximum limit Movement reduced

D5622 Tilt plate sensor 2 signal below minimum limit Movement reduced

D5715 Stop tilt plate Engine shutdown

D5744 Swashplate Double Failure Movement Reduced

D5745 Divergence of the tilt plate Movement is reduced

D5746 Tilt plate not responding Movement disabled

D5824 Safe start plate not in neutral Movement disabled

D5835 Emergency drain and safe start valve stuck on position Movement disabled

D5911 Overspeed error Movement reduced

D5915 Overspeed shutdown Engine shutdown

D5928 Overspeed error Movement disabled

D6202 Slow motion indicator, erroneous activation All functions are enabled

D6203 Slow motion indicator, erroneous shutdown All functions are enabled

D6302 Slow motion mode switch, erroneous activation All functions are enabled

D7002 High / low speed switch, erroneous activation (left lever) All functions are enabled

D7309 Low pressure in the service brake All functions are enabled

D7321 The pressure in the service brake is above the maximum permissible All functions are enabled

D7322 The pressure in the service brake is below the maximum permissible All functions are enabled

D8302 Stabilizers on / off valve output, erroneous activation All functions are enabled

D8303 Output of the valve on / off stabilizers, erroneous shutdown Control of stabilizers is not available

D8307 AVR ON / OFF valve output, open circuit AVR control not available

D8402 Feedback relay on / off stabilizers, erroneous inclusion All functions are enabled

D8403 Feedback relay on / off stabilizers, erroneous shutdown Control of stabilizers is not available

D8505 Left stabilizer lift output, short circuit to battery Control of stabilizers is not available

D8506 Left stabilizer lift output, ground fault Control of stabilizers is not available

D8507 Left stabilizer lift output, open circuit Control of stabilizers not available

D8605 Left stabilizer lowering output, short circuit to battery Control of stabilizers is not available

D8606 Left stabilizer lowering output, ground fault Control of stabilizers not available

D8607 Left stabilizer down output, open circuit Control of stabilizers is not available

D8705 Right stabilizer lifting output, short circuit to battery Control of stabilizers is not available

D8706 Right stabilizer lifting output, short to ground

D8707 Right stabilizer lift output, open circuit Control of stabilizers is not available

D8805 Right stabilizer lowering output, short circuit to battery Control of stabilizers is not available

D8806 Right stabilizer lowering output, ground fault Control of stabilizers is not available

D8807 Right stabilizer down output, open circuit Control of stabilizers is not available

D8902 Stabilizers activation switch, erroneous activation Stabilizers control is not available

D9099 Actuator calibration required Minimum current + tilt plate calibration All functions enabled

D9999 Invalid persistent data table not applicable

Service Code List - Workgroup Controller

The workgroup controller is located at the rear of the frame, to the left of the boom.

CODE DESCRIPTION RESULTS

W0321 Battery voltage above maximum limit Work equipment off

W0322 Low battery voltage below the minimum limit Work equipment off

W0721 Hydraulic oil temperature above maximum limit All functions enabled

W0722 Hydraulic oil temperature below minimum limit All functions enabled

W1005 PVG32 up / down valve, short to battery Boom up and down blocked

W1006 PVG32 up / down valve, ground fault Boom up and down blocked

W1028 PVG32 up / down valve, input error, main valve side diagnostics Boom up and down locked

W1105 PVG32 tilt valve, short to battery Tilt off

W1106 PVG32 tilt valve, short to ground Tilt off

W1128 PVG32 tilt valve, input error, main valve side diagnostics Tilt disabled

W1205 PVG32 extend / retract valve, short to battery Boom extend / retract blocked

W1206 PVG32 extend / retract valve, earth fault Boom extend / retract blocked

W1228 PVG32 extend / retract valve, input error, main valve side diagnostics Boom extend / retract blocked

W1305 PVG32 auxiliary valve, short to battery Auxiliary hydraulics disabled

W1306 Auxiliary valve PVG32, ground fault Auxiliary hydraulics disabled

W1328 PVG32 auxiliary valve, input error, diagnosis from the main valve side Auxiliary hydraulics disabled

W1405 PVG32 frame leveling valve, short to battery Frame leveling locked

W1406 PVG32 frame leveling valve, earth fault Frame leveling blocked

W1428 PVG32 frame alignment valve, input error, main valve side diagnostics Frame alignment blocked

W1824 Frame leveling potentiometer not in neutral Frame leveling locked

W3223 Invalid software or permanent data Work equipment off

W3228 Controller failure Work equipment disabled

W3296 Power off All functions enabled

W3297 Programmed by the controller All functions are enabled

W3304 No communication with gateway controller Work equipment is disabled

W3404 No communication with display controller Work equipment is disabled

W3604 No communication with the motor controller All functions are enabled

W3704 No signal from drive controller Auxiliary hydraulics disabled

W3804 No connection with LLMC Working group reduced

W3818 LLMC out of range Working group reduced

W3844 No LLMC compliance Working group reduced

W3845 No LLMC Compliance, Level 2 Stable Moves Disabled

W3904 No connection with LLMI Working group reduced

W3918 LLMI out of range Working group reduced

W4004 No communication with the joystick Work equipment is disabled

W4005 Joystick X-axis not in neutral (tilt) Tilt disabled

W4007 Joystick Y-axis not in neutral (lift) Lift disabled

W4010 Left joystick roller is not in neutral (extend and retract) Extend and retract disabled

W4028 Joystick handle failure Extend and retract disabled

W4204 No communication with receiver The orange carrycot error indicator on the transmitter flashes quickly. 3 beeps every 10 seconds on the transmitter.

W4205 Left joystick X-axis remote control disabled The orange cradle mode error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4206 Right joystick X-axis remote control disabled The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4207 Left joystick X-axis remote control disabled The orange cradle mode error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4208 Right joystick X-axis remote control disabled The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4215 Left joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4215 Left joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4216 Right joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4217 Left joystick Y-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4218 Right joystick Y-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4320 Carrycot mode. The remote control is not connected to the cradle wiring (from the receiver CAN bus signal). The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4321 Cradle mode. The remote control is not connected to the carrycot wiring (from the receiver's GACD controller status). The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4325 Cradle mode. Cradle detection error. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4326 Cradle mode. The cradle was not found on the supporting structure. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4327 Cradle mode. The carrycot was not found on the supporting structure when the GACD controller is on or the remote control is in operation. Orange carrycot error indicator on transmitter slowly

flashes. 3 beeps every 10 seconds on the transmitter.

W4330 Carrycot mode. Error in the operation of the cradle retraction switch. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4331 Carrycot mode. Expected boom extension not detected (boom retract switch on). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4335 Carrycot mode. Failure of the supports. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4336 Carrycot mode. The supports are not on the ground. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4340 Carrycot mode. Wrong arrow angle. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4341 Carrycot mode. Unexpected boom lift. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4342 Carrycot mode. No boom lift expected. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4343 Cradle mode. Boom angle exceeded. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4345 Cradle mode. LLM error. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4346 Carrycot mode. LLM in the lowered zone. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4347 Carrycot mode. Longitudinal stability: the maximum permissible value has been reached. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4350 Carrycot mode. Frame alignment failure. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4351 Carrycot mode. Boom alignment angle exceeded (out of range [-2 °; + 2 °]). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4355 Carrycot mode. Locking pin defective. The red lock indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter. W4356 Carrycot mode. The locking pin is unlocked. The red lock indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4360 Carrycot mode. Failure due to overload of the carrycot. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4361 Cradle mode. Overloading the cradle. The carrycot overload indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4365 Cradle mode. Incorrect angle of inclination. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4366 Cradle mode. Tilt angle exceeded (out of range [-4 °; + 4 °]). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4370 Cradle mode. FNR switch malfunction. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4371 Cradle mode. Parking brake malfunction. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4372 Cradle mode. Wrong position of the swivel washer. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W4404 Cradle mode. There is no communication with the GACD controller on the CAN bus. The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.

W4621 Supply voltage 5 V to the voltage sensor above the maximum limit Work equipment off

W4622 5 V voltage supply to voltage sensor below minimum limit Work equipment off

W6021 Signal from inclinometer sensor above maximum limit All functions enabled

W6022 Signal from inclinometer sensor below minimum limit All functions enabled

W6098 Calibration complete All functions enabled

W6099 Calibration required All functions enabled

W6102 Inclination indicator, switch-on error All functions enabled

W6103 Inclination indicator, shutdown error All functions enabled

W6521 Boom angle 1 above maximum limit All functions enabled

W6522 Boom angle 1 below minimum limit All functions enabled

W6621 Boom angle 2 above maximum limit All functions enabled

W6622 Boom angle 2 below minimum limit All functions enabled

W6744 Wrong boom angle All functions enabled

W6798 Boom angle calibration performed All functions enabled

W6799 Boom angle calibration required All functions enabled

W6802 Boom retract switch, short to battery All functions enabled

W6803 Boom retract switch, short to ground or open circuit All functions enabled

W8002 Quick-Tach power out, erroneous power-up Quick-Tach power function not available

W8003 Quick-Tach power out, erroneous shutdown Quick-Tach power function not available

W8007 Quick-Tach power output, open circuit Quick-Tach power is off

W8128 Quick-Tach Power Switch in Error State Quick-Tach Disabled

W8202 Quick-Tach power relay feedback, erroneous activation Quick-Tach function disabled

W8203 Quick-Tach power relay feedback, erroneous shutdown Quick-Tach function disabled

W8502 Platform Detect Switch Closed The orange cradle mode error light on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W8503 A short or open circuit in the work platform detection switch. The orange cradle mode error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.

W9999 Invalid workgroup controller table Applicable

Service Code List - Display Controller

Service Code List - LLMI System Controller

CODE DESCRIPTION RESULTS

L0102 Left panel button 1, erroneous activation Working light button does not work Cannot access calibration menu for control mode and battery voltage

L0202 Button 2 of the left panel, erroneous activation Joystick lock button does not work

Unable to change the state of the safety valve Unable to access the angle calibration menu

L0302 Button 3 left panel, erroneous activation Auxiliary hydraulics button does not work

Unable to change constant flow status Unable to access the pump menu of the drive

L0402 Left panel button 4, erroneous activation Information button does not work Cannot change the displayed menu

L7404 No communication with the main controller Data is not displayed / functions on the display are prohibited

L7672 Left panel software error Data not displayed / functions prohibited on display

Service Code List - LLMI System Controller

CODE DESCRIPTION RESULTS

I3014 LLMI system EEPROM failure LLMI is not displayed, workgroup functions are reduced

I3015 Failure of the external LLMI trigger signal

LLMI is not displayed, workgroup functions are reduced

I3018 Invalid RAM check LLMI LLMI is not displayed, workgroup functions are reduced

I3016 Incorrect check of the checksum of the LLMI program

LLMI is not displayed, workgroup functions are reduced

I3113 LLMI check button error Check not available

I3121 LLMI sensor ID error LLMI is not displayed, workgroup functions are reduced

I3122 LLMI sensor offset LLMI is not displayed, the functions of the working group are reduced

I3123 LLMI sensor reading out of LLMI range is not displayed, workgroup functions are reduced

I0314 Reception of LLMI sensor outside of LLMI delay is not displayed, workgroup functions are reduced

I0315 LLMI sensor failure LLMI is not displayed, the functions of the working group are reduced

I3014 LLMI calibration values out of range

LLMI is not displayed, workgroup functions are reduced

I3015 LLMI calibration values inverted LLMI not displayed, workgroup functions reduced

I3018 LLMI calibration values too close

LLMI is not displayed, workgroup functions are reduced

I3016 LLMI calibration timeout LLMI not displayed, workgroup functions reduced

I3113 Undervoltage LLMI LLMI is not displayed, the functions of the work group are reduced

I3121 Overvoltage LLMI LLMI is not displayed, the functions of the work group are reduced

Service Code List - LLMC Controller

CODE DESCRIPTION RESULTS

C3801 LLMC System EEPROM Failure Workgroup Functions Reduced

C3803 Failure of the external LLMC trigger signal Run group functions reduced

C3804 Invalid LLMC RAM Check Run Group Functions Reduced

C3805 Invalid LLMC Program Checksum Verification Workgroup Functions Reduced

C3017 LLMC Sensor ID Error Run Group Function Reduced

C3014 LLMC Sensor Offset Working Group Functions Reduced

C3015 LLMC sensor reading out of range Run group functions reduced

C3018 LLMC Sensor Reception Out of Delay Run Group Functions Reduced

C3016 LLMC Sensor Failure Run Group Functions Reduced

C3113 LLMC calibration values out of range Rungroup functions reduced

C3121 LLMC Calibration Values Inverted Run Group Functions Reduced

C3122 LLMC Calibration Values Too Close Workgroup Functions Reduced

C3123 LLMC Calibration Timeout Run Group Functions Reduced

C0314 LLMC undervoltage Working group functions reduced

C0315 LLMC overvoltage Working group functions reduced